Revision › Springs and elasticity › Worksheet

Springs and elasticity Hard

GCSE Physics · Forces · Name ____________________ Date ________

Builds on: Forces, weight and resultant force, Density and changes of state, Internal energy and latent heat

Do now

Quick questions on earlier topics - to get your brain going.

  1. Which of the following statements correctly describes a force? [1]

    1. It has both magnitude and direction.
    2. It has magnitude only.
    3. It is always contact.
    4. It cannot be represented by an arrow.
  2. Name one example of a contact force. [1]

  3. What is the density of a material if it has a mass of 8 kg and a volume of 2 m³? Express your answer in kg/m³. [1]

  4. During the density experiment with an irregular object, which of the following must be done to ensure accurate volume measurement? [1]

    1. D) Add salt to increase density
    2. C) Use a thermometer to measure temperature during measurement
    3. B) Record the water level before and after submerging the object
    4. A) Weigh the object inside the water

Practice

  1. Which of the following precautions is most important when measuring the spring constant using a hanging‑mass apparatus? [1]

    1. Use a spring that has already been stretched beyond its limit
    2. Ensure the mass does not hit the floor before equilibrium is reached
    3. Neglect the weight of the hanging mass if it is small
    4. Apply the largest possible mass to get a large extension
  2. A toy car’s bumper behaves like a spring. When the bumper compresses by 0.05 m under a load of 2 N, what is its spring constant? [2]

  3. A stretchable rubber band is fixed between two poles in a greenhouse. A pot weighing 5 kg hangs from it. The band stretches by 0.12 m before the pot reaches equilibrium. Assuming Hooke’s law applies, what is the magnitude of the force exerted by the pot on the band? (Take g = 9.8 s⁻²) [2]

  4. A spring has a spring constant of 40 N/m. A student adds masses sequentially until the total mass is 1.5 kg (weight = mg). What is the extension, in metres? Give your answer to two decimal places. [2]

  5. A spring with a spring constant of 150 N/m is stretched until its extension is 0.20 m. Calculate the force applied, in newtons. [2]

  6. A mass of 3 kg is hung from a vertical spring and the spring extends by 0.25 m before equilibrium is reached. If the spring constant k is expressed in newtons per centimetre (N·cm⁻¹), what is its value? (Use g = 9.8 s⁻²). Give your answer to two decimal places. [2]

  7. Which of the following is a necessary safety measure when performing the spring‑extension experiment? [1]

    1. Ensure the clamp stand is securely fastened to the bench.
    2. Use a ruler that can rotate freely.
    3. Keep all weights off the floor at all times.
    4. Place the spring on a soft cushion.
  8. A spring has a spring constant of 120 N/m and is stretched by 60 mm. Calculate the elastic potential energy stored (in J) to two decimal places. [1]

  9. An elastic rubber band stretches by 0.08 m when a force of 2.5 N is applied. Calculate the spring constant (k) of the rubber band, giving your answer to the nearest whole number (N/m). [1]

  10. A rubber band is stretched by 15 cm when a force of 4.5 N is applied. What is the spring constant in N/m? Give your answer to one decimal place. [1]

  11. An experimental spring was loaded with a series of weights, producing extensions as follows: weight 0 N gives extension 0 m; 49.5 N gives 0.05 m; 98.1 N gives 0.10 m. Using the linear relationship, calculate the spring constant to the nearest whole number (N/m). [1]

  12. An engineer uses a metal rod as a spring in a hinge. If pulling 5 N causes an extension of 0.02 m, what would be the extension if 12 N were applied, assuming linear behaviour? Give your answer to the nearest centimetre. [1]

Exam practice

Real past-paper questions on springs and elasticity, with their mark schemes, are in 4 Triangles - free to practise.

Mixed practice

Questions on topics this one links to - mixing them helps you remember both.

  1. A sealed container holds 5.0 g of carbon dioxide gas that occupies a volume of 400 cm³. Calculate the density in kg / m³, rounded to one decimal place. [2]

    (Density and changes of state)
  2. An electric door handle is pulled by a force of 25 N at a point 15 cm from the centre. What is the moment produced? [2]

    (Moments, levers and gears)
  3. A piece of aluminium has a mass of 3.6 g and occupies a volume of 1.4 cm³. Calculate its density in kg m⁻³, rounded to the nearest whole number. [2]

    (Density and changes of state)
  4. Which process will increase the internal energy of a closed system? A. Cooling the system B. Increasing its pressure while keeping temperature constant C. Heating the system D. Adding mass to the system [1]

    1. Heating the system
    2. Adding mass to the system
    3. Increasing its pressure while keeping temperature constant
    4. Cooling the system
    (Internal energy and latent heat)
  5. When conducting an experiment to measure the momentum of two colliding trolleys using a light‑gate system, which device is essential for accurately recording each trolley's velocity? [1]

    1. A stopwatch
    2. A barometer
    3. Light gates
    4. A thermometer
    (Momentum)
  6. A delivery van with a mass of 1800 kg is moving at a constant speed of 12 m s⁻¹ along a straight road. What is the magnitude of its momentum? Give your answer in kg m s⁻¹. [1]

    1. 19200 kg m s⁻¹
    2. 21600 kg m s⁻¹
    3. 20000 kg m s⁻¹
    4. 18000 kg m s⁻¹
    (Momentum)

💼 Where it leads: Cycle mechanic · Crane driver · Motor mechanic · Road traffic accident investigator - more

Stuck, or finished? Scan for help on springs and elasticity - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk

Answers

  1. A It has both magnitude and direction.
  2. friction
  3. 4
  4. C B) Record the water level before and after submerging the object
  5. B Ensure the mass does not hit the floor before equilibrium is reached
  6. 40
    Use F = k e k = F/e = 2 / 0.05 = 40
  7. 49
  8. 0.37
    Weight = 1.5×9.8=14.7 N; e = F/k = 14.7/40 = 0.3675 ≈0.37
  9. 30
    Use F = k e = 150 × 0.20 = 30
  10. 1.18
  11. A Ensure the clamp stand is securely fastened to the bench.
  12. 0.22
    e = 0.06 m; Ee = ½ k e² = ½×120×0.06² = 0.216 J ≈ 0.22 J
  13. 31
    k = F / e = 2.5 N ÷ 0.08 m = 31.25 N/m
  14. 30
  15. 990
    k = F/e = 49.5/0.05 = 990 N/m
  16. 5
    k = F/e = 5/0.02 = 250 N/m; e = F/k = 12/250 = 0.048 m = 4.8 cm ≈ 5 cm
  17. 12.5
    5 g = 0.005 kg; 400 cm³ = 4×10⁻⁴ m³; density = 0.005 ÷ 4×10⁻⁴ = 12.5 kg/m³.
  18. 3.75
    Convert centimetres to metres: 15 cm = 0.15 m. Then use M = F × d.
  19. 2570
  20. A Heating the system
  21. C Light gates
    Light gates give precise time between gate crossings → velocity.
  22. B 21600 kg m s⁻¹
    p = mv = 1800 × 12

Some key word definitions from Oak National Academy (Open Government Licence).

Stuck, or finished? Scan for help on springs and elasticity - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk