Revision › GCSE Maths › Geometry and measures

Bearings and measuring

GCSE Maths · Geometry and measures. Explained 2 ways - start with the one that suits you.

Bearings and measuring Start here

Measuring lines, angles and bearings helps read maps and scale drawings.

Key words

bearing
a direction expressed as a degree on a compass
acute angle
an angle less than 90°

How to do it

  1. Use a ruler to measure the length of any line.
  2. If it’s a map, convert the measured length using the scale given.
  3. Read an angle with a protractor; note the degree value.
  4. Name the angle type – acute if <90°, right if =90°.

Watch out for

  • Wrongly guessing AB’s length; remember to read directly.
  • Inaccurate measurements: always measure close to the line centre.
  • When scaling decimals, multiply correctly – avoid adding fractions of the scale factor.

Remember: Keep each step clear and check your units before writing the final answer.

Bearings and measuring Stretch

You need to be able to read a map, work out angles between bearings, calculate missing sides and then translate that into a bearing for the required direction.

Key words

bearing
angle measured clockwise from true north; expressed in degrees or as a compass‑point (e.g. 037° = N NE).
reverse bearing
add/subtract 180°, wrap to 000–359°. Example 073° → 253°.
interior angle at B
smallest positive difference between the two bearings that meet at B; use modulo 360 to avoid >180° values.

How to do it

  1. Note each known bearing and distance.
  2. If a compass‑point is used, convert it to three‑figure (N=000°, NE=045°, etc.).
  3. Find the interior angle at the common vertex by subtracting the two bearings; if the result >180° replace it with 360° minus that value.
  4. Use the cosine rule to calculate a missing side: \(c^2=a^2+b^2-2ab\cos C\).
  5. Use the sine or cosine rule again to find the required angle, then add (or subtract) it from a known bearing to obtain the unknown bearing.

Watch out for

  • Don’t subtract the two bearings directly if they cross the 0/360° line; first normalise both to 000–359° and then take the smaller positive difference.
  • If you reverse a bearing by just adding 180°, remember that 180+200=380 becomes 020°. Mistakes in this step give wrong interior angles.
  • Using a decimal value such as 8.7 km, be careful when multiplying by another number; do not split the multiplication into whole and fractional parts incorrectly – treat it as one precise product before rounding later.

Remember: Bearings run clockwise from true north; add an interior angle to move clockwise, subtract to go counter‑clockwise. Perform all calculations to at least three decimal places before final rounding.

✏️ Try 3 quick questions

  1. A line has a bearing of 070° from A to B. What is its reverse bearing? (Students often subtract from 360°.)

  2. Two places are 12 km apart. On a map they are 3 cm apart. What is the scale of the map, expressed as kilometres per centimetre?

  3. A bus route on a map has a bearing of 045°. The scale is 1 cm = 500 m and the straight‑line distance between the two stops shown on the map is 4.8 cm. What is the actual ground distance in metres?

Practise it with real exam questions

4 Triangles has quick questions on bearings and measuring, real GCSE past-paper questions with their mark schemes, and a revision plan that picks what to work on next.

Try the quick questions

📝 Worksheets and a knowledge organiser to print

Questions on this topic for a lesson, homework or revision - a quick "do now", misconception questions, small steps that change one thing at a time, and practice, with answers on the last page.

Easy Medium Hard 📄 Knowledge organiser

🔤 Key words to know

Bearing
A bearing is an angle measured in degrees from North in the clockwise direction and written with three figures.
Transversal
A transversal is a line, line segment, or ray that intersects through two or more lines at distinct (different) points.
Corresponding
Corresponding angles are a pair of angles at different vertices on the same side of a transversal in equivalent positions.
Alternate
Alternate angles are a pair of angles, both between or both outside two line segments, that are on opposite sides of the transversal that cuts them.
Co-interior
Co-interior angles are on the same side of the transversal line and in between the two other lines.
Angle
An angle is a measure of turn. It is often displayed as the rotation between two line segments.
Reflex angle
An angle that is greater than a straight line (i.e. greater than 180°) is a reflex angle.
Proportionality
Variables are in proportion if they have a constant multiplicative relationship.
Ratio
A ratio shows the relative sizes of 2 or more values and allows you to compare a part with another part in a whole.

Many definitions from Oak National Academy (Open Government Licence).

When it's usually taught: Year 10 - Bearings.

💼 Where it could take you

Jobs where people use this every day - whichever way you go after school.

Straight from school or an apprenticeship

With college or an advanced apprenticeship

With a degree

Each job opens its National Careers Service profile: what it pays, the hours, and how to get in.

📺 Watch a lesson on this

Each is a maths lesson by Oak National Academy licensed under Open Government Licence (OGL). Lessons open on Oak National Academy's site.

More on Geometry and measures