Revision › Internal energy and latent heat › Worksheet
Internal energy and latent heat Hard
GCSE Physics · Particle Model of Matter · Name ____________________ Date ________
Builds on: Density and changes of state, Gas pressure, Pressure in fluids
Do now
Quick questions on earlier topics - to get your brain going.
What is the density of a material if it has a mass of 8 kg and a volume of 2 m³? Express your answer in kg/m³. [1]
During the density experiment with an irregular object, which of the following must be done to ensure accurate volume measurement? [1]
- D) Add salt to increase density
- C) Use a thermometer to measure temperature during measurement
- B) Record the water level before and after submerging the object
- A) Weigh the object inside the water
A container of gas has a volume of 0.10 m³ and is at a pressure of 80 kPa. The temperature is kept constant while the pressure increases to 160 kPa. What is the new volume of the gas? Provide your answer in m³. [1]
Air occupies a fixed volume of 0.02 m³ at a pressure of 100 kPa. If the temperature is kept constant and the pressure is raised to 250 kPa, what will the new volume be? Give your answer in m³. [1]
Practice
Which process will increase the internal energy of a closed system? A. Cooling the system B. Increasing its pressure while keeping temperature constant C. Heating the system D. Adding mass to the system [1]
- Heating the system
- Adding mass to the system
- Increasing its pressure while keeping temperature constant
- Cooling the system
Which definition correctly describes latent heat? A. The amount of energy required to raise the temperature of a substance by 1 °C. B. Energy supplied that changes the internal energy without changing temperature during a phase change. C. Energy needed to compress a gas at constant volume. D. Heat lost by a body in thermal equilibrium with its surroundings. [1]
- Energy needed to compress a gas at constant volume.
- Heat lost by a body in thermal equilibrium with its surroundings.
- Energy supplied that changes the internal energy without changing temperature during a phase change.
- The amount of energy required to raise the temperature of a substance by 1 °C.
Which of the following is a necessary safety precaution when performing the experiment to determine the specific latent heat of fusion of water? [2]
- Wear protective gloves and eye protection while handling hot equipment.
- Ensure that the ice sample is at exactly 0 °C before it is added to the calorimeter.
- Keep the calorimeter completely insulated from the surrounding environment.
- Use a metal spoon that can be heated directly in the calorimeter.
In measuring the latent heat of fusion of water using a calorimeter, which statement is correct? A. It is acceptable for some heat to escape to the surroundings. B. The ice must be at exactly 0 °C before the experiment starts. C. A stirring rod should not be used during the measurement. D. All of the above [1]
- The ice must be at exactly 0 °C before the experiment starts.
- A stirring rod should not be used during the measurement.
- All of the above
- It is acceptable for some heat to escape to the surroundings.
A 0.5 kg block of aluminium (specific heat capacity = 900 J kg⁻¹ °C⁻¹) is heated from 20 °C to 80 °C. Calculate the change in internal energy, ΔE, in joules. [3]
A 0.45 kg block of copper (specific heat capacity = 385 J kg⁻¹ °C⁻¹) receives 2.5 kJ of energy from a heating element. What is the temperature rise, to one decimal place, in °C? [2]
Which of the following best describes latent heat? A. Energy stored as potential energy only. B. Energy required for a change of state at constant temperature. C. Energy released when a substance freezes. D. Energy needed to increase the mass of a substance. [1]
- A
- D
- C
- B
The specific latent heat of fusion of ice is 334 kJ kg⁻¹. How many kilograms of ice melt when 1000 kJ of energy is supplied? Give your answer to one decimal place. [1]
Which statement is incorrect about heating water? A. Heat added increases temperature until 100 °C. B. Once 100 °C is reached, all further heat causes phase change to steam. C. No temperature change occurs during boiling if heat continues to be supplied. D. Water will instantly turn into steam at 100 °C regardless of pressure. [1]
- B
- A
- C
- D
What must be used in an experiment measuring the latent heat of fusion of water to minimise heat loss? A. A heat‑insulated calorimeter. B. Adding salt to increase boiling point. C. Cooling the water before heating. D. Using a larger beaker to maximise surface area. [1]
- D
- A
- B
- C
A 2 kg block of copper (c = 385 J kg⁻¹ °C⁻¹) is heated at a constant rate of 500 W. How many seconds will it take to raise its temperature by 30 °C? Give your answer as an integer. [1]
A 3 kg block of iron (specific heat capacity = 450 J kg⁻¹ °C⁻¹) is heated from 25 °C to 75 °C. How many kilojoules of energy are required? Give your answer rounded to the nearest integer. [1]
Exam practice
Real past-paper questions on internal energy and latent heat, with their mark schemes, are in 4 Triangles - free to practise.
Mixed practice
Questions on topics this one links to - mixing them helps you remember both.
A sealed container holds 5.0 g of carbon dioxide gas that occupies a volume of 400 cm³. Calculate the density in kg / m³, rounded to one decimal place. [2]
(Density and changes of state)Which footwear will exert a greater pressure on the ground per unit area? A Snowshoes with an area of 0.5 m². B High‑heeled shoes with an area of 0.05 m². C Bare feet with an area of 0.1 m². D All footwear exert the same pressure if weight is equal. [1]
- D
- C
- B
- A
A piece of aluminium has a mass of 3.6 g and occupies a volume of 1.4 cm³. Calculate its density in kg m⁻³, rounded to the nearest whole number. [2]
(Density and changes of state)A sealed piston contains a fixed mass of gas at an initial pressure of 200 kPa and volume of 0.05 m³. The pressure is increased to 300 kPa while the temperature remains constant. Using Boyle’s law, calculate the new volume of the gas. Give your answer to one decimal place in litres. [2]
(Gas pressure)Which of the following precautions is most important when measuring the spring constant using a hanging‑mass apparatus? [1]
- Use a spring that has already been stretched beyond its limit
- Ensure the mass does not hit the floor before equilibrium is reached
- Neglect the weight of the hanging mass if it is small
- Apply the largest possible mass to get a large extension
A toy car’s bumper behaves like a spring. When the bumper compresses by 0.05 m under a load of 2 N, what is its spring constant? [2]
(Springs and elasticity)
Still going? Unlimited questions on internal energy and latent heat, marked as you go: 4triangles.co.uk
💼 Where it leads: Solar panel installer · Insulation engineer · Heat pump engineer · Gas service technician - more
Stuck, or finished? Scan for help on internal energy and latent heat - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk
Answers
- 4
- C B) Record the water level before and after submerging the object
- 0.05
- 0.008
- A Heating the system
- C Energy supplied that changes the internal energy without changing temperature during a phase change.
- A Wear protective gloves and eye protection while handling hot equipment.
- A The ice must be at exactly 0 °C before the experiment starts.
- 27000
- 14.4
- D B
- 3
- D D
- B A
- 46
- 68
- 12.5
5 g = 0.005 kg; 400 cm³ = 4×10⁻⁴ m³; density = 0.005 ÷ 4×10⁻⁴ = 12.5 kg/m³. - C B
- 2570
- 33.3
p₁V₁ = p₂V₂ → V₂ = (p₁V₁)/p₂ = (200 kPa × 0.05 m³)/(300 kPa) = 0.0333 m³ = 33.3 L - B Ensure the mass does not hit the floor before equilibrium is reached
- 40
Use F = k e k = F/e = 2 / 0.05 = 40
Some key word definitions from Oak National Academy (Open Government Licence).
Stuck, or finished? Scan for help on internal energy and latent heat - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk