Revision › GCSE Physics › Particle Model of Matter

Internal energy and latent heat

GCSE Physics · Particle Model of Matter. Explained 3 ways - start with the one that suits you.

Internal energy and latent heat Start here

Understand how heating changes energy, temperature or state.

Key words

internal energy
total kinetic plus potential energy of all particles in a system
specific heat capacity (c)
energy needed to raise 1 kg by 1 °C
latent heat (L)
energy per kg that changes the state at constant temperature

Key points

  • Decide if the problem involves only a temperature rise or a phase change.
  • Use ΔE = m c Δθ for temperature changes; use E = m L for phase changes.
  • Insert mass, c or L and Δθ (or 1 kg) into the chosen equation.
  • Carry out the calculation, keeping units consistent (kg, J/kg°C, °C, J).

Watch out for

  • Check that the energy supplied is not used to raise temperature; it all goes into melting.
  • Remember: ΔE and E are both measured in joules (J).
  • Units of c are J kg⁻¹ °C⁻¹, units of L are J kg⁻¹.

Remember: Use the right equation for the situation – temperature change or phase change.

Internal energy and latent heat Core

Understand how heating changes a system’s internal energy and how phase changes absorb energy without changing temperature.

Key words

internal energy
total kinetic + potential energy of all particles inside a system

Key points

  • Identify the system and whether only a temperature rise or a phase change occurs.
  • Use ΔE = m c Δθ for a temperature rise, with mass in kg, c in J kg⁻¹°C⁻¹ and Δθ in °C.
  • Use E = m L when a phase change happens; choose L_f for fusion or L_v for vapourisation.

Watch out for

  • Internal energy rises if heating increases particle motion; it can also rise through a phase change without temperature change.
  • The specific heat capacity tells how much energy is needed to raise the temperature of 1 kg by 1 °C. The specific latent heat tells how much energy per kg is needed for a phase change at constant temperature.

Remember: Apply ΔE = m c Δθ for temperature changes and E = m L for phase changes; keep all units consistent.

Internal energy and latent heat Stretch

Secure pupils should be comfortable with the two core equations: for heating, ΔE=m c Δθ, and for a phase change, E=m L. The key is recognising when temperature rises (use c) versus when it stays constant (use L).

Key points

  • Identify whether the process changes temperature or just state; if Δθ≠0 use c.
  • Convert masses to kilograms before using the equations.
  • For heating, compute ΔE = m c Δθ – all energy goes into kinetic energy of particles, raising T.
  • During a phase change no temperature change occurs; all supplied energy changes the internal structure and is called latent heat.
  • Use E=m L for the specific latent heat (fusion or vapourisation). L_f for solid→liquid, L_v for liquid→gas.
  • When multiple stages occur, calculate each ΔE or E separately then sum – no energy is lost between stages if isolated from surroundings.;7. Check units: J = kg·J kg⁻¹·°C → cancel to joules; latent heat also in J/kg gives J after multiplication by m.

Watch out for

  • Remember that temperature changes are always handled with the specific heat capacity, while phase changes use latent heat; mis‑applying c to a flat section of a heating curve gives wrong answers.
  • Graphs of heating/cooling will show flat plateaus when Δθ=0 – those indicate latent heat is being absorbed or released; never assume a temperature rise there.

Remember: Link this to the energy‑transfer topic: the internal energy change calculated here equals the net heat added, because no work is done in these closed systems.

✏️ Try 3 quick questions

  1. Calculate the change in thermal energy (ΔE) when 0.3 kg of iron is heated from 25 °C to 40 °C. The specific heat capacity of iron is 450 J kg⁻¹ °C⁻¹. Give your answer in joules to the nearest joule.

  2. Which of the following best describes latent heat? A. Energy stored as potential energy only. B. Energy required for a change of state at constant temperature. C. Energy released when a substance freezes. D. Energy needed to increase the mass of a substance.

  3. Which process will increase the internal energy of a closed system? A. Cooling the system B. Increasing its pressure while keeping temperature constant C. Heating the system D. Adding mass to the system

Practise it with real exam questions

4 Triangles has quick questions on internal energy and latent heat, real GCSE past-paper questions with their mark schemes, and a revision plan that picks what to work on next.

Try the quick questions

📝 Worksheets and a knowledge organiser to print

Questions on this topic for a lesson, homework or revision - a quick "do now", misconception questions, small steps that change one thing at a time, and practice, with answers on the last page.

Easy Medium Hard 📄 Knowledge organiser

🔤 Key words to know

Melting
the change of state from a solid to a liquid; happens at a fixed temperature for pure substances.
Boiling
the change of state from a liquid to a gas; happens at a fixed temperature for pure substances.
Specific latent heat
the change in energy when 1 kg of a substance changes state.
Specific heat capacity
the change in internal energy when the temperature of 1 kg of a substance changes by 1°C.
Change of state
changing from a solid to a liquid or liquid to gas (or the reverse).

Many definitions from Oak National Academy (Open Government Licence).

When it's usually taught: Year 10 - Energy of moving particles.

💼 Where it could take you

Jobs where people use this every day - whichever way you go after school.

Straight from school or an apprenticeship

With college or an advanced apprenticeship

With a degree

Each job opens its National Careers Service profile: what it pays, the hours, and how to get in.

📺 Watch a lesson on this

Each is a science lesson by Oak National Academy licensed under Open Government Licence (OGL). Lessons open on Oak National Academy's site.

More on Particle Model of Matter