Current, potential difference and resistance Start here
Learn the key ideas for GCSE physics.
Key words
current
rate of electric charge flow
Key points
Circuit diagrams use fixed symbols: battery (+‑), resistor (zig‑zag), switch (open line) and diode (triangle slash). Draw and read them.
Current (I) is the rate of electric charge flow. Charge (Q) is measured in coulombs; I = Q/t, so \(Q=It\).
Potential difference (V) or voltage is energy change per charge between two points. Resistance (R) limits current. Ohm’s law links them: \(V=IR\).
To find resistance you measure the voltage across a component and its current, then divide: \(R=V/I\). The same current flows at every point in one closed loop.
Watch out for
Remember that voltage, current and resistance must be in consistent units (V, A, Ω).
Remember: The relationship V = IR holds for any component if you measure the correct values.
Current, potential difference and resistance Core
You need to know how current flows, what the symbols mean and how to decide if a component is ohmic or not. The key ideas are listed below.
Key points
Standard circuit diagram symbols must be used correctly – battery (+‑), resistor (zig‑zag), switch (break line) and diode (triangle with slash).
Electric current (I) is the rate of flow of charge: Q = I t, where Q is in coulombs, I in amperes and t in seconds.
In a closed loop the same current flows through every component; currents at a node add to zero.
For any component V = I R. A higher resistance gives less current for the same voltage, and vice‑versa.
An ohmic conductor (constant temperature) has a straight‑line V–I graph – its resistance stays constant while I changes.
Non‑linear elements such as filament lamps, diodes, thermistors and LDRs show curved V–I graphs because their resistance varies with temperature or light.
Watch out for
(1 mark) The component is a filament lamp.
Remember: Always check whether the data show a straight‑line V–I relationship (constant R) or a curve; this tells you if the element is ohmic or variable.
Current, potential difference and resistance Stretch
Recall the core relationships: current is charge per time, all points of a loop carry equal current, and for any component \(V = I R\). Ohmic parts give straight‑line V–I graphs; non‑linear elements (filament lamp, diode, thermistor, LDR) show curved curves. Use these ideas to identify components from limited data.
Key words
current
rate of flow of electric charge
potential difference
voltage across a component
Key points
In circuit diagrams use the standard symbols: battery +‑, resistor zig‑zag, switch break line, diode triangle with slash.
Electric current \(I\) is defined by \(Q = I t\); it has the same value at every point of a closed loop.
For any component the relation \(V = I R\) holds; higher resistance gives lower current for the same voltage.
Ohmic conductors produce straight‑line V–I graphs, so their resistance is constant when temperature is unchanged.
Non‑linear elements (filament lamp, diode, thermistor, LDR) change resistance with current or temperature, giving curved V–I curves.
Watch out for
Only one potential is given; do not assume linearity without further points.
Check that you are using \(V = I R\) and not mixing units – volts for V, amps for I, ohms for R.
Remember the sign convention: a diode conducts only in forward bias; a filament lamp’s current rises slowly with voltage.
Remember: Use \(R=\frac{V}{I}\) to test if resistance stays constant; a straight‑line V–I curve indicates an ohmic resistor, curvature points to a filament lamp or other non‑linear element.
✏️ Try 3 quick questions
A battery supplies 12 V. A resistor of unknown resistance is connected, producing a current of 0.4 A. Calculate the resistance using V = IR.
Tick one box. Which statement best describes an Ohmic conductor?
A small LED uses a constant current of 30 mA when it is on for 3 h each day. How many coulombs of charge does it use in one day? Give your answer to the nearest whole number.
There are more on this in 4 Triangles, with hints and worked answers, and real past-paper questions. Carry on there.
Practise it with real exam questions
4 Triangles has quick questions on current, potential difference and resistance, real GCSE past-paper questions with their mark schemes, and a revision plan that picks what to work on next.
Questions on this topic for a lesson, homework or revision - a quick "do now", misconception questions, small steps that change one thing at a time, and practice, with answers on the last page.