Understand how wires connect components so you can calculate currents and voltages.
Key words
current
flow of electric charge, measured in amperes (A)
Key points
In a series circuit the same current flows through every component.
The battery voltage splits over each part; add up to the total supply voltage.
Total resistance is R_total = R1 + R2 + … ; adding one resistor raises this value.
Watch out for
Remember that adding resistors in parallel always lowers the total resistance, but you need not calculate it for two resistors.
Remember: You only have to solve series problems, but knowing the ideas helps with any test.
Series and parallel circuits Core
In a series circuit all components share one wire, so current is identical through each. Supply voltage splits across them and total resistance is the sum of resistances. In parallel each branch has the same voltage; currents add and overall resistance is lower than any single resistor.
Key words
series
components connected end‑to‑end so the same current flows through each
parallel
branches side‑by‑side with identical voltage across every branch
resistance
opposition to current, measured in ohms (Ω)
potential difference
voltage, measured in volts (V)
Key points
Remember that the same current flows through every component of a series circuit.
Use Ohm’s law: \(V = I R\) to relate voltage, current and resistance for each part.
Add all individual resistances to get the total resistance of the series circuit: \(R_{total}=R_1+R_2+…\).
The supply voltage is split across the components; the sum of all drops equals the source voltage.
For parallel circuits, recognise that the voltage on each branch is the same as the supply voltage and the total current from the battery equals the sum of branch currents.
Watch out for
In a series circuit the total resistance is never lower than any single resistor.
Do not add resistances for parallel branches; instead remember that the combined resistance will be less than the smallest individual resistor, but you are not required to calculate this in GCSE work.
Always use Ohm’s law consistently – check units when plugging values.
Remember: In a series circuit, current is the same through all elements, voltage divides among them, and total resistance sums. This lets you solve most basic series problems.
Series and parallel circuits Stretch
In a series circuit the same current flows through every component, so voltage drops add up to the supply voltage. In parallel each branch has the same potential difference but the total current is the sum of the currents in the branches. Adding resistors in series raises the overall resistance; adding them in parallel lowers it.
Key words
current
electric charge per second, measured in ampere (A)
potential difference
voltage between two points, measured in volt (V)
resistance
opposition to current flow, measured in ohm (Ω)
Key points
In a series circuit the current through each component is identical.
The total voltage of a supply equals the sum of all individual voltage drops.
Total resistance of series resistors adds: R_total = ΣR_i.
In parallel each branch experiences the same voltage as the source.
The total current from the source equals the algebraic sum of currents in every branch.
Two parallel resistors give an overall resistance smaller than any single resistor; no calculation of this is required for GCSE but remember R_total < min(R1,R2).
Watch out for
Do not forget that series circuits use the same current for all elements – this rule often saves time.
In parallel problems the supply voltage is fixed; you must calculate each branch’s current separately before adding them if asked.
Students sometimes misapply the resistance formula for two resistors in parallel – the specification does not require this.
Remember: Series circuits are commonly used for measurement and testing because a single, uniform current runs through every part of the circuit. This property is useful when measuring voltage across individual elements with a voltmeter that draws negligible current.
✏️ Try 3 quick questions
In a series circuit, what quantity is the same through every component?
Adding a second resistor in series to an existing circuit will _______.
2. For two resistors of 4 Ω and 6 Ω, which statement correctly compares their total resistance when wired in series versus in parallel?
There are more on this in 4 Triangles, with hints and worked answers, and real past-paper questions. Carry on there.
Practise it with real exam questions
4 Triangles has quick questions on series and parallel circuits, real GCSE past-paper questions with their mark schemes, and a revision plan that picks what to work on next.
Questions on this topic for a lesson, homework or revision - a quick "do now", misconception questions, small steps that change one thing at a time, and practice, with answers on the last page.