Revision › Mains electricity and safety › Worksheet
Mains electricity and safety Easy
GCSE Physics · Electricity · Name ____________________ Date ________
Builds on: Current, potential difference and resistance, Series and parallel circuits
Do now
Quick questions on earlier topics - to get your brain going.
A battery supplies 12 V. A resistor of unknown resistance is connected, producing a current of 0.4 A. Calculate the resistance using V = IR. [1]
Which step should you do before measuring the resistance of a component with an ohmmeter? [1]
- ☐ Connect one lead across the component's terminals only
- ☐ Place the component in the circuit to maintain its temperature
- ☐ Heat the component to 100 °C
- ☐ Remove the component from any power supply and ensure it is disconnected from other circuits
In a series circuit, what quantity is the same through every component? [1]
Tick one box: Which statement about a series circuit is correct? [1]
- A) The total resistance equals the product of the resistances.
- B) The same current flows through every component.
- C) Each resistor has a different voltage drop regardless of size.
- D) The power supply's potential difference is divided equally among all components.
Practice
A microwave consumes 1.2 kW and is used for 5 minutes each day for a week. How much energy, in joules, does it use in total? (Hint: 1 kW = 1000 W). [1]
An electric heater uses 4 kW of power from mains. Calculate the current it draws (in A). Round to one decimal place. [1]
A space heater draws a current of 10 A from the mains supply, which has a potential difference of 230 V. What power does the heater use? Give your answer in watts. [1]
Which colour identifies the live conductor in a three‑core cable? [1]
A small appliance draws a current of 7 A from the mains. Using a potential difference of 230 V, calculate its power in watts. Use the formula P = IV and give your answer to the nearest whole number. [1]
A garden light plugs into mains and draws 5 A. What is its power in watts? Assume the mains potential difference is 230 V. [1]
A 200 W kettle is switched on for 3 minutes. How many joules of energy are transferred to the water? Use the formula E = P × t. [1]
Stretch
A step up - try these if you finish.
A hair dryer draws a current of 4 A from the mains supply. Calculate its power consumption. Use \(P = V\times I\) where \(V = 230\,V\). [2]
Which component in a plug protects the appliance from over‑current? [1]
- Neutral wire
- Earth wire
- Live wire
- Fuse
An electric heater uses 1800 W on the mains supply. What current does it draw? Round your answer to the nearest whole ampere. [2]
Between which of the following does the live wire have a higher potential difference relative to earth? [1]
- Both are equal
- The mains supply at 230 V
- A 12 V battery
- Neither has a potential difference
Mixed practice
Questions on topics this one links to - mixing them helps you remember both.
Which statement best defines a renewable energy source? A) It can be used once and then depleted B) It is not produced from natural processes C) It is replenished naturally over human timescales D) It only comes from fossil fuels [1]
- It only comes from fossil fuels
- It can be used once and then depleted
- It is replenished naturally over human timescales
- It is not produced from natural processes
Which statement about wind energy is incorrect? A) It can produce electricity when there is no sunlight. B) Its output depends on wind speed. C) It has a small land footprint. D) It emits CO₂ during operation. [1]
- It has a small land footprint.
- Its output depends on wind speed.
- It can produce electricity when there is no sunlight.
- It emits CO₂ during operation.
When measuring the voltage across a resistor with a multimeter, which setting should you use? [1]
- C) ACV 1000 V
- D) Continuity test
- B) DCV 200 V
- A) Auto‑range
When measuring the resistance of a component with a multimeter, which precaution should you take? [1]
- Keep the device on while measuring to keep it warm.
- Touch both leads simultaneously for better contact.
- Disconnect the power supply before connecting the meter.
- Use the highest voltage setting on the meter.
If a constant voltage supply is used and the resistance in a circuit increases, what happens to the power consumed by the load? [1]
- A) Power increases
- B) Power stays the same
- C) Power decreases
- D) Power first increases then decreases
In the equation Q = It, what does I stand for? [1]
(Current, potential difference and resistance)
Still going? Unlimited questions on mains electricity and safety, marked as you go: 4triangles.co.uk
💼 Where it leads: Smart meter installer · Electricity distribution worker · Electrician · Auto electrician - more
Stuck, or finished? Scan for help on mains electricity and safety - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk
Answers
- 30
- D ☐ Remove the component from any power supply and ensure it is disconnected from other circuits
- current
- B B) The same current flows through every component.
- 2520000
- 17.4
- 2300
P = VI = 230 × 10 - Brown
- 1610
- 1150
- 36000
- 920
- D Fuse
- 8
- B The mains supply at 230 V
- C It is replenished naturally over human timescales
Renewable means it renews on a human timescale, so C is correct. - D It emits CO₂ during operation.
Wind energy produces power only where there is wind; it does not emit CO₂ in normal operation. Hence D is false. - C B) DCV 200 V
- C Disconnect the power supply before connecting the meter.
- C C) Power decreases
- Current
Some key word definitions from Oak National Academy (Open Government Licence).
Stuck, or finished? Scan for help on mains electricity and safety - an explanation, hints and unlimited practice that marks itself.
Free at 4triangles.co.uk